Anatec Maxboat Catamaran Oak + DEVO7 Lithium Battery + ALF500 Fishfinder

Anatec Maxboat Catamaran Oak + DEVO7 Lithium Battery + ALF500 Fishfinder, The boat is a catamaran MAXBOAT type initiator, its typical form, ensures a perfect buoyancy and stability in any event even in the most extreme conditions (wind and waves). On each side of the hull, two broken engines give the power to navigate more than 7 km / h at full load (about 2 meters per second). The control of these motors is done independently of each other thereby steer the boat with incredible precision. This feature ensures perfect handling of the boat maxboat initiator and gives it the ability to turn in place. This is a major advantage when removing the lines must be very precise (along or under a canopy). Able to carry up to 5 kg of bait (2.5kg per bin), the max boat can deposit a large amount of bait in one single trip. Each tray has a separate opening, this feature increases the stability of the boat navigation while being capable of initiating multiple lines each way. Equipped with high quality electronic components, the boat max boat initiator respects the charter of quality and reliability common to all Anatec boats. A complete model with multiple functions for fishermen who want extreme put the odds on their side for a successful fisheries. Usable in any circumstance, the boat Anatec maxboat initiator has a ramp 6 high-visibility LEDs on the front and two red LEDs on the back. To facilitate the transport and the placing in water, Anatec maxboat is provided with a handle. Commissioning and launching the boat Implementation of the main batteries. The batteries are supplied charged, but it may be useful to hand them over several hours during the first use of the boat. Before connecting the batteries, make sure the power switch is in the OFF position. Remove the cover by unscrewing the fixing butterflies, place the batteries in the housing provided for this purpose (each side of the hull) and perform their connection. Turning on the remote control. The DEVO 7 remote control works with eight 1.5V AA. To power the remote control, push the main switch to "ON" position (switch up). Closing the boat cover, Center the cover on the two plastic screws. Insert it gently and put butterflies tightening moderately. Turning on the boat, Before positioning the main switch to the ON position, make sure: - The remote is on and the battery charge level is satisfactory. - The batteries are connected properly in the boat. Launching and operation of the boat, Before navigating the vessel, it is preferable to perform a preliminary test run of the various components. If everything works correctly, follow the launching before removal. Remote DEVENTION DEVO7, The MAXBOAT come with DEVENTION DEVO7 remote that has 2.4GHz technology. This new technology is the ultimate in terms of remote control, it allows to solve the problems of unfortunate interference that cause the opening of the hatch or the dropping of lines at the wrong time. Also, when multiple users are within range, it is no longer necessary to make a change for quartz tuning to radio frequencies. The allocation of different channels automatically. Finally this new technology no longer requires an antenna on the boat, which greatly facilitates access under low branches. These new remotes, the transmission range up to 250m allowing to exclude any risk of loss of control. For his protection, the remote control is accompanied by a clear plastic cover that allows its use in case of rain. It is important to never use the remote control in the rain without protection. Charging the batteries and autonomy, Connect the output lead from the charger to the battery to be charged. Connect the charger to a power outlet 220 Volts. The charging time is 6 hours for a battery to 7.4V 12000mAh. Once charging is complete, disconnect the charger from the power outlet and disconnect Color fishfinder ALF500, The LFA 500 is an echo sounder usable wireless transmission of all initiators of the range boats Anatec. If you have opted for a model ship equipped with an echo sounder original ALF500, the following instructions will familiarize you with the various functions. If you chose a version of non- equipped boat, note that it is possible to obtain and assemble yourself sounder on your boat. In this case you receive a kit with the parts needed for assembly. Sonar elements are: A reception housing (screen) with standalone antenna. An electronic transmission housing (transmitter). A power switch to enable or disable the sounder. One power supply A transmitting antenna (on the boat). A probe with seal and nut. An orange rubber probe adapter (Catamaran and Maxboat only). A Velcro to attach the transmitter on some boats. An antenna extension (for Pacboat and Maxboat only) The setting of this parameter affects the sensitivity of the probe. When the water is clear and there is a lot of background, it is recommended to increase sensitivity. Conversely, when the water is cloudy or agitated it is better to decrease the sensitivity to reduce clutter. Note that the sensitivity is in automatic mode by default. Fish ID Sensitivity, This determines the display mode of detected echoes. When activated, the sounder analyzes the echo returns and differentiates those fish who are just inert objects or structures. The echoes are transcribed in the form of a small icon fish. You can adjust the sensitivity level of the "fish ID" to eliminate the weakest and keep only the strongest signals. It is important to understand that the sonar cannot always make the difference between a fish or floating object between two waters, so it is possible that you watch a fish there or there is none. To analyze the maximum layers of water, we recommend disabling the "fish ID" function and only study the actual echo returns. Scale Depth, This defines the maximum depth shown on the screen, that is to say the depth corresponding to the horizontal line at the bottom of the screen. The possible ranges are 5, 10, 15, 20, 30 and 50 meters. If the depth scale is in AUTO the receiver mode adapts itself according to the scale of depth. The surface of the water line is 0 and the depth is represented by a dotted line. It is very useful to estimate the depth at which the fish are found depending on the depth scale shown at the bottom left of the screen Night Mode, By activating this mode, the screen background becomes black and the backlight intensity decreases. It is also possible to remove the key beeps for more discretion. Note that the display brightness can also be adjusted in the "Backlight" menu. Radio channel, This setting will allow you to avoid interference problems with other pollsters nearby. 20 receiving channels are available. Backlight, Enables screen illumination with 10 different levels of brightness. Background Color, Select the screen background color that suits you best. White, blue or black.